banner

How to repair LED work lights?

20 Published by admin Nov 18,2019

LED work lights have become a favorite illuminant for ordinary home users because of their energy saving,high brightness,long life and low failure rate.However,the low failure rate does not mean that there is no fault.What should we do when the LED work light fails?Too extravagant!In fact,the cost of repairing LED work lights is very low,and the technical difficulty is not high,and ordinary people can operate.

Working of led detail


CM-9036|36w LED Cube With Dual Side Light

Lamp bead damage

After the LED work light is turned on,some of the lamp beads are not lit,and it can be basically judged that the lamp bead is damaged.The damaged lamp bead can generally be seen with the naked eye-there is a black spot on the surface of the lamp to prove that it has been burned.Sometimes the lamp bead is connected in series and then in parallel,so if one lamp bead is lost,it will cause one lamp bead to be off.

We offer two repair options based on the number of lamp bead damage.

First,a small amount of damage

If only one or two lamp beads are broken,we can repair them in two ways:

1.Locate the broken lamp bead and connect the metal at both ends with a wire to short it.The effect of this is that most of the lamp beads can be lit normally,and only the individual beads that are broken are not bright,which has little effect on the overall brightness.

2.If your hands-on ability is strong,you can go online to buy the same type of lamp beads,and replace it yourself-use the electric iron(the blower blows for a while)to heat the old lamp beads until the glue on the back of the old lamp beads After melting,remove the old LED work lights lamp beads with tweezers(do not use your hands,too hot).At the same time,put the LED work lights new lamp beads on the heat(pay attention to the positive and negative poles),you're done!

Working of led front


CM-9036|36w LED Cube With Dual Side Light

Second,a lot of damage

If the lamp bead is damaged in a large amount,it is recommended to replace the entire lamp bead.The lamp bead is also available on the Internet.Pay attention to three points when purchasing:1.Measure the size of your own lamp;2.Look at the appearance of the lamp bezel and the starter connector(explained later);3.Remember the output of the starter.Power range(explained later)LED work lights.

These three points of the new lamp bead must be the same as the old lamp bead board-it is very simple to replace the lamp bead board.The old lamp bead board is fixed on the lamp holder with screws,and it can be directly removed.The new lamp bead board is fixed by a magnet.When replacing,remove the new lamp bead board and connect the connector of the starter.


CM-9036|36w LED Cube With Dual Side Light

Starter damage

The faults of most LED lights are all on the starter-if the lamp is not lit at all,or if the lamp fails to flash after the lamp is turned on,the starter is broken.

The starter can't be repaired,it can only be replaced,but the new starter is not expensive.Pay attention to three points when purchasing a new launcher:

1.Pay attention to the appearance of the connector-the appearance of the starter connector is as follows(if the starter is male,the lamp bead is the female;vice versa)

2.Remember if your lamp can change color and change colors.The new launcher must have the same amount of discoloration as the old launcher.

3.Remember the output power range of the starter-a range will be marked on the starter,as long as the power of the bead is within this range.

It is still very simple to replace,first separate the starter and the lamp bead,and the starter is also fixed on the base with screws,and can be removed.The new starter is also a magnet,sucked and connected to the lamp bead.

ISO9001 certified and has perfect quality control system.

Chiming LED  Auto Light Factory have evolved and expanded our technology in new LED lights and k...

Do you like ? 274

Read more

work light supplier factory has expanded

Our  factory has expanded, and the total area of the plant has reached 10 thousand square meters....

Do you like ? 226

Read more

Chiming Light bar manufacturer New standardized equipment

We introduced a number of new standardized equipment: EMC tester, IP67 tester, simulated vehicle ...

Do you like ? 224

Read more

Chiming vehicle work lights China factory brand enterprise prix

Grand prix annual bilboard of China automotive liting brand: We won the  LED vehicle work lights ...

Do you like ? 231

Read more

Led automotive light manufacturer acquisition of design patents

Led automotive light manufacturer acquisition of design patents.   Led automotive light manu...

Do you like ? 207

Read more

Guangzhou Chiming Electronic CO., Ltd.
No.82 hantang West Road ,hantang Village,renhe Town,haiyun District, Guangzhou,China.
Share it:
FAQ
Q1 .Are you manufacturer or trade company?

Chiming:We are one of the earliest automotive LED lights manufacturers in China.

Q2.Can you produce according to the samples?

Chiming: Yes, we can produce by your samples or technical drawings. We can build the moulds according your need.

Q3.Do you test all your goods before delivery?

Chiming: Yes, we have 100% test before delivery

Q4. How do you make our business long-term and good relationship?

Chiming:We keep good quality and competitive price to ensure our customers benefit

Q1 .Are you manufacturer or trade company?

Chiming:We are one of the earliest automotive LED lights manufacturers in China.

Q2.Can you produce according to the samples?

Chiming: Yes, we can produce by your samples or technical drawings. We can build the moulds according your need.

Q3.Do you test all your goods before delivery?

Chiming: Yes, we have 100% test before delivery

Q4. How do you make our business long-term and good relationship?

Chiming:We keep good quality and competitive price to ensure our customers benefit

Q1 .Are you manufacturer or trade company?

Chiming:We are one of the earliest automotive LED lights manufacturers in China.

Q2.Can you produce according to the samples?

Chiming: Yes, we can produce by your samples or technical drawings. We can build the moulds according your need.

Q3.Do you test all your goods before delivery?

Chiming: Yes, we have 100% test before delivery

Q4. How do you make our business long-term and good relationship?

Chiming:We keep good quality and competitive price to ensure our customers benefit

Q1 .Are you manufacturer or trade company?

Chiming:We are one of the earliest automotive LED lights manufacturers in China.

Q2.Can you produce according to the samples?

Chiming: Yes, we can produce by your samples or technical drawings. We can build the moulds according your need.

Q3.Do you test all your goods before delivery?

Chiming: Yes, we have 100% test before delivery

Q4. How do you make our business long-term and good relationship?

Chiming:We keep good quality and competitive price to ensure our customers benefit

Guangzhou Chiming Electronic CO., Ltd. All rights reserved
| Sitemap |
Technical Support: Baiila